ASTM C42 FREE PDF

Home  /   ASTM C42 FREE PDF

This standard is issued under the fixed designation C42/C42M; the number . of core test results.2 and that is free of is the individual responsible for analysis or. ASTM C42/C42M () Standard Test Method for Obtaining and Testing Drilled ASTM International, West Conshohocken. Free SCIRP Newsletters>> . ASTM C Potential Resistance to Degradation. In-situ Tests . Determine time from start until no free water is on ASTM C42, Coring, 3 cores/5, sf.

Author: Nalkree Vigul
Country: Papua New Guinea
Language: English (Spanish)
Genre: Spiritual
Published (Last): 27 April 2010
Pages: 161
PDF File Size: 17.70 Mb
ePub File Size: 8.40 Mb
ISBN: 301-9-64918-338-6
Downloads: 56799
Price: Free* [*Free Regsitration Required]
Uploader: Faek

The ends shall be sawed or ground to tolerance or capped in accordance with capping procedures for hardened concrete specimens of Practice C SI units are shown in brackets.

Ends are not to be capped. The acceptance criteria for core strength is to be established by the specifying authority. Therefore, results of two properly conducted tests on cores sampled from the same hardened concrete where a single test is defined as the average of two observations coreseach made on separate adjacent drilled 4 in.

ASTM CC42M – 04 – Free Download PDF

Cores for Compressive Strength 7. If this is not practical, removal of concrete can proceed if the cut surfaces do not display erosion of the mortar and the exposed coarse aggregate particles are embedded firmly in the mortar. Originally published as C 42 — 21 T.

fred Thus, these factors should be applied to high-strength concrete with caution. If time permits, the concrete should not be removed before it is 14 days old. BoxFarmington Hills, MI A number in parentheses indicates the year of last reapproval.

ASTM C42-C42M – 04

Sampling and sample preparation requirements are given to ensure that dimensional requirements are met and that the specimens are comprised of intact sound concrete as free of flaws as the particular structure will allow.

  LA SEXTA VIA PATRICIO STURLESE PDF

This standard has been approved for use by agencies of the Department of Satm. Average values are given in the table.

Measure core diameters to the nearest gree. They are applicable to both dry and wet concrete for strengths between and psi [14 to 42 MPa].

C42-Obtaining and Testing Drilled Cores and Sawed Beams of Concrete

Measure the lengths of such cores in accordance with Test Method C It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. When the line of contact is not straight or contains projections or depressions having heights or depths greater freee 0.

When capping is employed the caps shall be as thin as practicable and shall be formed of high-strength gypsum plaster. Cap or grind the cores, and test them within 48 h of receipt. A specimen taken perpendicular to a vertical surface, or perpendicular to a surface with a batter, shall be taken from near the middle of a unit of deposit when possible c442 not near formed joints or obvious edges of a unit of deposit.

Last previous edition C 42 — awtm If necessary, saw the ends of the specimens until the following requirements are met: Current edition approved Feb.

When grinding or capping of the bearing surfaces is. Core specimens with length-to-diameter ratios less than 1. NOTE 2—Prior to capping, the density of a core may be determined by freee it and dividing it by the volume calculated from the average diameter and length, or by any other standard method for determining density.

The preferred length of the capped specimen is between 1. Significance and Use 3. Length of Drilled Cores 6. C 39 with the sstm of the following information: The values stated may not be exact equivalents, therefore each system must be used independently of the other.

  DESIGNCON 2003 TEC FORUM I2C BUS OVERVIEW PDF

NOTE 3—Correction factors depend on various conditions such as moisture condition, strength level, and elastic modulus. Parte 1 de 2 Designation: Determine the average diameter by averaging two measurements taken at right angles to each other about the midheight of the specimen.

ACI provides core strength acceptance criteria for new construction. In-place test methods may be used to estimate the level of strength development prior to attempting removal of concrete samples. When preparing strength test specimens from samples of hardened concrete, samples that show defects or samples that have been damaged in the process of removal shall not be used. The relationship is affected by many factors such as the strength level of the concrete, the in-place temperature and moisture history, and the strength gain characteristics of the concrete.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Combining values of the two units may result in nonconformance. Core diameters less than 3. If the ratio of the length to the diameter of the core specimen exceeds 2.

NOTE 1—It is not possible to specify a minimum age when concrete is strong enough to withstand damage free removal, because the strength at any age depends on the curing history and strength grade of the concrete. For strengths above psi [70 MPa], test data on cores show that the correction factors may be larger than the values listed above.

The saw shall have a diamond or silicon-carbide cutting edge and shall be capable of cutting specimens which conform to the prescribed dimensions, without excessive heating or shock. Do not use specimens with projections or depressions greater than 0. Livro sobre Cimento Portland e Concreto.