ASTM F2054 PDF

Home  /   ASTM F2054 PDF

ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. Consult Labthink Instruments Co., Ltd.’s High Pressure Leak Tester for Package ASTM F, ASTM F brochure on DirectIndustry. Page: 1/4. More help in interpreting the results can be found in ASTM F Inflation Seal Strength Testing (ASTM F and F), including burst, creep and creep-to-.

Author: Meztigrel Miramar
Country: Slovenia
Language: English (Spanish)
Genre: Photos
Published (Last): 4 February 2018
Pages: 276
PDF File Size: 17.26 Mb
ePub File Size: 3.81 Mb
ISBN: 888-7-36568-521-6
Downloads: 71904
Price: Free* [*Free Regsitration Required]
Uploader: Felmaran

Tensile Tester for both compression and tensile, with loads typically N. See Appendix X4 for information. By placing the package within restraining plates during pressurization, asgm dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed. This standard does not purport to address all of the safety concerns, if any, xstm with its use.

Flexible packages, aseptic packages, various plastic pilfer-proof closures, flexible tubes, caps and other materials. Labthink RT rub tester to test on flexo printing. Test Methods F describes methods of burst testing that wstm not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

Satm test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal. By placing the package within restraining plates during pressurization, the asmt stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

See Appendix X4 for information. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

Seal Strength system to test 3 sides seal bags. FT-F1 Fogging tester to to test for fogging on upholstery material and time frame for testing. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. Thickness micron testing equipment with Resolution 0. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

  FONETICA Y FONOLOGIA ANTONIO QUILIS PDF

This allows the test to have a higher probability of detecting the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package. In particular it is intended as applicable to packages astn seals that have a peelable seal feature peeled open by end user to remove contents of package. Labthink provides COF Tester for coef.

ASTM F | Rycobel

Oxygen Permeability Qstm to test containers. This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, aztm so required. Historical Version s – view previous versions of standard. MFY Leak Tester is used to look for pin holes in bags that hold calibration solutions for medical instruments.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine f22054 applicability of regulatory limitations prior to use. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal.

Link to Active This link will always route to the current Active version of the standard. Vacuum Leak Tester for bottles for food, chemical and pharmaceutical applications.

ASTM F2054/F2054M – 13

Reference Appendix X3 for further information f0254 calculation of stress factors and structural design considerations. The Online Industrial Exhibition. Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates.

This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used. COF Inclined Plane Tester Measure the static coefficient of friction of various materials aastm a variable inclined plane and a sliding block. Active view current version of standard. An indicator of the minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity.

  ALPINE IVA-W200 MANUAL PDF

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. Link to Active This link will always route to the current Active version of the standard.

MFY leak detector for our pouch packaging. Three Tests in one instrument High Pressure Leak tester With various accessories for tests of different packages Applications: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

This test method cannot provide a measure of package seal uniformity. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations f22054 to use.

See Appendix X2 for further information. Specifications Test Range Contact: Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as asym of the standard.

Pressure differentials may occur during such processes as sterilization and transportation. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.