Don’t forget about our other 2Wire HG-G info that you might be interested in. Login to 2Wire HG-G Router · Change your 2Wire HG-G IP Address. You might find additional types of support and download options at your service provider’s website. For example, a search for “2Wire” at AT&T’s. Rec’vd my 2wire hg-b and the DSL light is green but will not connect to Internet (Internet light is red or off) I have my username.
|Published (Last):||17 September 2011|
|PDF File Size:||1.96 Mb|
|ePub File Size:||10.60 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 62 Configuration Key Code The key at&h associated with the current provisioning settings. Configuration parameters for modules listed in the Advanced Link Manager States page.
Regulatory Information Repair of this equipment should be made only by the 2Wire Service Center or a 2Wire authorized agent. Check wt&t manuals to make sure that their HTTP management page ip addresses are different – say By default, the 2Wire gateway ships with WEP enabled and a preconfigured network name.
Attach the computer to the Local Network port of the 2Wire gateway. Declaration of Conformity Trade Name: Please enter a valid email address. The direct link to the manual for the SBG is http: This link is present only if the 2Wire gateway is VoIP-enabled.
During 2Wire gateway 2wure, Channel 6 is the default, and allowing both to compete on 2wie same channel is a bad idea – give each its own wi-fi channel.
Configure the Wireless Network Page The MTU Maximum Transmission Unit is the largest size packet or ,anual, specified in octets eight-byte bitsthat can be sent from a computer to the network. Your can reset your 2Wire HG-B in the following way s: It should work if you don’t have a router.
Management and Diagnostic Console To view information about each node, click the node link.
Block Ping IP address for example, Ethernet home network interface, the number of payload bytes received, and the number and percentage of received packets in error. Broadband Link Tab This chapter describes the 2Wire gateway Broadband Link features, and provides detailed instructions on how to customize your broadband settings. Web site could be affected by many different factors. Compliance Information Compliance Information The 2Wire HG product family has been tested, and is compliant to the following standards: The Troubleshooting — Resets page allows you to reset various components associated with the 2Wire gateway network.
The radio frequency band the access point uses for your wireless network the default is 6. Les Dickinson Level 3 Expert Answers. From the Connection Type drop-down menu, select the connection type: Port Corresponds to the SIP proxy destination port. Page 23 The Data Errors panel displays the following information. The Advanced — Configure Services page allows you to enable the 2Wire gateway to operate in bridged mode, change the timeout settings for NAT, enable notification messages, enable the SIP ALG, and change the upstream maximum transmission rate.
Ask a Question Usually answered in minutes! Number of Lines Displays the number of lines allowed on the gateway.
Posted by mbaurhyte on Mar 17, Node Information Description Link status Up. Modifying the settings on this page can impact the ability of computers on the local network to access the broadband connection.
In the Host field, enter the URL of the host location to which you wish the 2Wire gateway to send the ping or traceroute.
To set your system password: Page Management and Diagnostic Console To manually set the time and date: Login to post Please use English characters only. Configuring The Firewall advanced These features should 270h1g-b used only if you are thoroughly familiar with firewalls and networking. Technical support representatives use this information to help troubleshoot problems with your broadband connection.
The Management and Diagnostic Console provides information about the status of the 2Wire gateway, its broadband network connections, attached home networking devices, system and security information, and a running log of any error conditions.
Just as the post office delivers mail to your home address, servers know to deliver data to your nanual based on your IP address. Try your internet connection after doing it. The Advanced – Static Routes page allows you to manually configure static routes that specify the transmission path data must follow between devices on the gateway network.
Wireless this field is present only on wireless 2Wire gateway models Transmit The cumulative number of frames transmitted over the Management and Diagnostic Console To create an application profile: The email address entered is already associated to an account.
The Edit Application page opens. From the Ring Tone pull-down menu, select the tone you wish to associate with the phone. The 2Wire gateway then uses this external address to communicate with the Internet on behalf of devices connected to the local network. If you have performed a reset of your HG-B device or not changed the defaults, you should be able to access it with the following settings:.
Wait 10 seconds and plug the power back. Delay of latency Measurement of how much path delay is introduced. To ensure that the settings cannot be changed, in the Password field enter a password. If the value is between 1 to minutes, the PPP session will timeout if the 2Wire gateway does not detect outbound traffic destined for the Internet in the specified time.