AUROMATIC 620 2 PDF

Home  /   AUROMATIC 620 2 PDF

Operating manual for remote control unit VR 90 _ 2. 1 Notes on the of the auroMATIC and VRC modular bus con-. Installation instructions Mixer module VR 60 _ 2. Contents. 1. Notes on the documentation. . of the auroMATIC or VRC controllers and. Find great deals for Vaillant Solar System Regulator auroMATIC / VRS /3 . Shop with Picture 1 of 4; Picture 2 of 4; Picture 3 of 4; Picture 4 of 4.

Author: Nikojar JoJot
Country: Syria
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 July 2010
Pages: 477
PDF File Size: 5.46 Mb
ePub File Size: 13.82 Mb
ISBN: 552-5-57243-907-5
Downloads: 56831
Price: Free* [*Free Regsitration Required]
Uploader: Meztizshura

Setting the solar gain to zero The temperature of this hot water as it leaves the boiler is referred auronatic as the flow temperature. VR 10 standard sensor Fig. The next stage is only switched on if the current target system value has not yet been attained or exceeded at the end of this time.

Vaillant Solar System Regulator auroMATIC / VRS /3 | eBay

Weather-controlled The outside temperature is measured by a separate sensor which is mounted in the open air, and the results are transmitted to the controller. The solar gain is reset to zero and will be recalculated from this point onwards. Malfunction caused by incorrect wiring! See the VPM W manual.

You set a unique bus address on the VR 32 using a rotary switch. If more than two heaters are to be connected in cascade, a bus coupler is required for each aromatic to connect it to the eBus Western socket. The basic data consisting of day of the week, date, time of day and outside temperature auromatc always shown in the upper area of the display. Setting the solar gain to zero Allows you to set the value of the cylinder gain to zero. Mon-FriMon-Fri The identification plate is readily visible on the left side of the controller base.

  ADVERTISING MANAGEMENT BY BATRA MYERS AND AAKER PDF

The mixer remains in its current position They are used mainly as buffers to store the solar energy supplied by the collector. Holiday programming 4 for whole system Periods When the hot water target value is attained, the post-heating boiler is switched 60.

The flow temperature in the heating circuit gets warmer the lower the outside temperature becomes.

A settable timer programme, independent of the cylinder charging programme, can be used for this circulation pump. Do not cover regulators Do not cover your regulators with furniture, drapes or similar objects.

This standard code is displayed in Menu 8 and is also accessible to the owner. None, On, Off, Auto Energy sav. All the connected system components, including the heat sources, are activated sequentially andautomatically detected. You can, for example: In hydraulic plan 9, the reheating is initiated by the VPM W fresh water unit. The dispaly shows the system status. A maximum of six mixer modules can be connected. Setting time windows In Menu 3 Time programmes, you can set time windows for the heating circuits, the DHW cylinders and the circulation pumps.

auroMATIC – Busmodular control system for solar supported heating – Vaillant

These system components are drawn in broken lines or in grey in the plans. The default setting as-supplied condition is for automatic changeover not to take place. These menus are identified by a ‘C’ and a number at the top right of the display.

  GLORIANA MOORCOCK PDF

Target room temperature Room Temp. Selecting the hydraulic plan Faults may only be rectified by a qualified expert technician.

You can thus define different heating times for each day according to your daily routine. Consequently, the room can not be heated satisfactorily and an uncomfortable feeling of coolness prevails the same effect is produced when doors between heated or unheated or slightly heated rooms remain open. Dispose of the old unit and any accessories professionally. In the 60 in the Operator level you can, for example, set the room temperature, time windows, night set back temperatures and heating curves entirely to your individual requirements.

In the case of the circulation pump the time windows determine the operating times.

auroMATIC 620

Information System set temp. When a cascade is constructed, a separate bus coupler is required for each heater. The controller is supplied with one of the following external sensors: This transports the heated solar fluid to the point of measurement more quickly. Cylinder charging auronatic and connected circulation pumps always have the same operating mode.

Vaillant Solar System Regulator auroMATIC 620 / VRS 620/3

Solar-assisted heating is used to extract solar heat even for heating purposes. Solar circuit 1 Information collector sensor Status solar pump Oper. Factory setting — Day: