BeagleBoard-xM is based on the TI DM and delivers increased performance . The schematic and PCB remain the same as revision C1. BeagleBoard-xM LCD7. System Reference Manual. Revision B. Page 2 of THIS DOCUMENT. This work is licensed under the Creative. BeagleBoard-xM Rev C System Reference Manual Revision April 4, Page 1 of REF: BB_SRM_xM. BeagleBoard-xM System Reference Manual.
|Published (Last):||11 November 2004|
|PDF File Size:||12.1 Mb|
|ePub File Size:||6.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
Optional Battery Location Figure Select the decompressed image file and correct SD card location. Page 19 of DM37x Block Diagram Page 65 of By setting this value in the control register, this signal will be routed to the corresponding pin of the expansion connector.
To download all files at once please click here. Schemtaics of Contents Add to my manuals Add. Figure 51 is the design of the expansion connector and the interfaces to the processor.
If you are trying mx reuse an SD card that has already been xk under the above process, you will need to reformat the card to erase the second parttion. It some cases, the BeagleBoard may not work if the display timing is not accepted by the display. This may require a change in the software running on the Beagle.
This page was last edited on 2 Aprilat Page 45 – Figure Content originally published on LinuxDevices. The connector is mounted on the bottom side of the board.
Comments are beagleboarc property of their submitters. Camera Connector Page – Figure Overview JTAG debugging interface 7.
Page 38 – Figure All derivative works are to be attributed to Gerald Coley of BeagleBoard. Table Of Contents B It is not intended to provide detailed documentation of the processor or any other component used on the board.
Page – Power Page – Table FAT has been dropped from version 2. Views Read View source View history. A standard male to female straight DB9 cable may be used or you can use a USB to serial adapter that will plug directly into the board without the need for any other cables.
Page – Table Page of Go. Reset Circuitry Page 65 – Figure It should be noted that the voltage level of these signals are 1. Figure 6 shows the location of the USB Host connectors.
Audio Out Plug Page – Figure Beagleboard Accessories This section covers these accessories and add-ons and provides information on where they may be obtained. Page 54 of This interface is not amplified and may require the use of amplified speakers in certain instances.
The ULPI used on the BeagleBoard keeps this down to only 12 signals because it combines just three control signals, plus clock, with an 8-bit bi-directional data bus.
If this a fresh card, one that has never been used, you can skip to step Figure 16 shows the location of the microSD connector. Unlike on the original version of the Beagle, a straight through non null modem cable is required.
Linux is a registered trademark of Linus Torvalds. P11 Lcd Signals Whether or not the Beagle will support those monitors is dependent on the timings that are used on the BeagleBoard and those that are accepted by the monitor. JTAG debugging interface 7.
Power Connector Figure 52 is a picture of the BeagleBoard power connector with the pins identified. If desired, the resistors can be installed to pull the signals schenatics. Revision C2 Reference Manual BeagleBoard Specification This section covers the specifications of the BeagleBoard and provides a high level description of the major components and interfaces that make up the BeagleBoard.
Changed POP memory part number due to obsolescence of the current device.
Remove the USB cable and re insert. All boards will be returned via standard mail if an issue is found.
For more information, see http: You can use this to make measurements, check dimension on the PCB, beaglegoard look at each layer to analyze the routing used. Covered in this section are a few of the accessories that may be used with BeagleBoard. Figure 11 shows the proper connection point for the cable. Reference Manual The expansion header is provided to allow a limited number of functions to be added to the BeagleBoard via the addition of a daughtercard.