Owner’s Manuals. Below, you may find manuals for your Beretta firearm in an electronic format. You may also order a hard copy if desired. Owner’s Manuals. Unofficial Beretta Site: really neat site, complete with the history of the model 92 series, old ‘owner’s manual, exploded views, 70 (Thanks to Ed Ruesing, he gave me the opportunity to post the manual) KB, English AL ( KB). The illustrations and instructions in this article are based on the Beretta Urika , but they are also valid for the other versions of the

Author: Zololl Fenrilkis
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Automotive
Published (Last): 10 December 2010
Pages: 385
PDF File Size: 4.48 Mb
ePub File Size: 17.63 Mb
ISBN: 955-5-99934-737-5
Downloads: 90218
Price: Free* [*Free Regsitration Required]
Uploader: Kizuru

With no plug, capacity is 1 and 3. The ring looks like stainless.

Lower the hammer on the unloaded gun by pulling the trigger. The safety button is held in place by a plunger and spring on the right side. Les illustrations et les descriptions contenues dans ce prospectus ne sontdonnees qu’a titre indicatif. With the cap off, hold a rag over the end of the spring, pull the nail out, and let the spring come out gently.

Putting the trigger group back in is just the reverse – remember to press the bolt release button while you put it in. The valve does not need any adjustment – just tighten the valve nut all the way down, then tighten the counter nut.

All manhal, disassembly and maintenance procedures should be carried out with the firearm unloaded magazine tube empty, receiver empty and cartridge chamber empty. The fore- end is correctly assembled when there is no space left between the parts.

Beretta – Unofficial Beretta Site

Fortunately, that can be done without disassembling the nut. The use of reloaded or remanufactured ammunition can in- crease the likelihood of excessive cartridge pressures, casehead ruptures or other defects in the ammunition which can cause damage to your firearm and injury to yourself or others nearby. Ugika focus of this article is disassembly and reassembly, not cleaning and maintenance, although I make a few comments on those issues.


Once you work the ring part way up, you can grab it with thin-nosed pliers and a,391 it on out.

I guess the clip is on there to keep a new owner from thinking he got a broken gun if he turns the gun down with the forend nut off, and the plug falls out.

Reassembly of the trigger group: Disassembly of BerettaIllustrated Posted: Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Search the history of over billion web pages on the Internet.

To invert the safety button: That is one of the reasons you should make sure the gun is cocked and put the safety on before you start to remove either the bolt or the trigger group. The bore and cartridge chamber must be clean and free from ob- structions.

This operation must be carried out by a competent gunsmith. If necessary, pull with pliers padded to prevent damage, or tie a strong cord to it and jerk.

The stock drop and cast of the spacer c must always correspond to those of the metal plate j.

Full text of “Beretta AL Urika”

The piston part 48 normally remains on the magazine cap shaft part 45but if the gun is dirty it may stick inside the gas cylinder on the barrel. Other measures of stock drop can be obtained using the supplied extra set of spac- ers.

A friend of mine puts it in the other way on purpose, because he says he can clean the gas ports urkka taking the valve apart that way. In fact, if you only use your gun for hunting, and you use fairly clean-burning shells, you might get away with never disassembling it. Now slide the whole works down into the receiver.


• Disassembly of Beretta

Never look into the muzzle or change tubes on a loaded gun even with safety engaged. Some bullets can travel over a mile. Very nice Mr Ben! Remove the hammer spring. A very nice and knowledgeable post indeed! This article does not apply at all to the Beretta gas-operated guns that have the recoil spring in the forearm older Lark series and the current Urkia nor to Beretta’s recoil-operated shotguns ES Pintail or Victoria.

If that is OK, the bolt probably went into the receiver cocked a little bit to one side. The gas ports can then be cleaned by sticking any suitable probe through the hole in the underside of the gas cylinder, going all the way through the cylinder and into the ports in the barrel.

If not, depress it completely. The moving part, which I call the “plunger” for lack of another name, is bigger in diameter so it fits close in the nut without a ring. Mon Feb 26, Put the carrier on. For more information, see: The only reason for doing this first is it will probably fall out anyway, so you might as well get it over with. To remove it, use a thin blade or similar tool to press the plunger in and push the button out to the left side of the trigger group.

Should the breech bolt release button be pressed in this condition, the breech bolt would slam forward and would stop only when the cocking handle hits the forward rim of the ejection port.

It will work either way well, you know that, if you have been putting it in the other way.