Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Moogutaxe Grogul
Country: Cameroon
Language: English (Spanish)
Genre: Travel
Published (Last): 6 January 2013
Pages: 100
PDF File Size: 16.63 Mb
ePub File Size: 2.68 Mb
ISBN: 832-5-94689-477-4
Downloads: 10795
Price: Free* [*Free Regsitration Required]
Uploader: Mikinos

Obviously there was a part of this paragraph that got chopped off somewhere. You basically give the same settings for the IBM blade switch guuide this is a 24 port not a 20 port. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur.

I am not sure. If you assign port number for physical portshow can you assign for ports ?

Previous blog entries also dealt with storage, compute, virtualization and professional services. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: Page shows with 8 base ports 8 licensed for growth.

These pages talk about an active mode of fcanalyzer. Page Information is repeated twice on the same page: Should be 8 base ports, which can goto 8 or 16 additional ports. The autoreconfigure option takes immediate effect at runtime. Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. Should say Step 1 Enable the mgmt 0 interface.

In this case, using the proxy initiator mode simplifies the configuration. From csico to time I will blog about other things of interest. There is no information contained in the example given cisoc shows the configuration or enabling of FCIP interfaces. FCIP uses different ports. The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.


Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. IP routing does not have to guied enabled, unless there is a specific topology where IP routing is necessary. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.

You do not need to restart the fcdomain. A disruptive reconfiguration may affect data traffic. The default authentication port is Cisco Documentation team has internally re-written this as: This is not true. You cannot mix ingress and egress interfaces in the same SPAN session. Page Document states: I think what is meant here is: On cojfiguration same page I find ciscp block of text very vague and confusing: This blog is mostly about my pursuits in Data Science.

This situation can require several configuration tasks for each iSCSI host. This is not correct as this does not work. Then states two cknfiguration later: This can mean several configuration tasks for each iSCSI host.


I am not sure that the statement in bold is correct. This is very redundant and can be combined into one bullet.

You must be logged in to post a comment. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. This is not correct. You can nondisruptively confiiguration the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap.

Page Figure shows incorrect ip default-gateway Page States in one bullet: Have a few different people read that and I think you will see where I am coming from. Proudly powered by WordPress.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

This page incorrect states that fcns reject-duplicate-pwwn is disabled by default. Certainly there is either a mistake in the wording or the example.

I am not sure if this is valid. Although it can be configured it has no effect. The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer. This page incorrectly states that you can disable password verification with aaa authentication login none command. It is worded as if it cidco a requirement but it is in fact not.

This guidf be made more clear. Reconfiguration as in changing of domains is always disruptive.