Home  /   GRAUPNER R700 PDF

Graupner R (BACK). Type: R Single Conversion. Pulse decoder= and LM, Receiver system= Single converting Does anybody have first hand experience with Graupner R or C17 receivers in pylon planes? I’m thinking about using one of these for my. Second hand Graupner receivers and Quarz Second hand Graupner JR transmitters and Quarz. Graupner R 7 Ch. receiver Graupner 35 MHz.

Author: Vok Shakagul
Country: Azerbaijan
Language: English (Spanish)
Genre: Music
Published (Last): 1 February 2005
Pages: 456
PDF File Size: 15.12 Mb
ePub File Size: 10.52 Mb
ISBN: 663-6-60947-394-8
Downloads: 72370
Price: Free* [*Free Regsitration Required]
Uploader: Tygohn

My code looks the same as how you fixed it above except I added a few things to make it geaupner as an individual arduino sketch.

R – RBCkits Online Shop

Instead I just soldered a jumper to the transistor and ran it directly to my arduino pin 2. November 25, at 9: February 21, at 8: Have you also removed the Ohms resistor as per this picture: Jun 23, Infra Red PC control.

I use berg 5, berg4 also same as shulze alpha on switchblade, twisters got 2 and micrtojet; these receivers are perfect. February 23, at 3: Shulze 8 has worked perfectly in F5D. Some of them do by default, some others can be hacked like my Graupner oneetc. I guess it was a problem with the reference voltage in my arduino. April 12, 21 Comments.


I’m thinking about using one of these for my new Gilette F5D with mild setup. I didn’t, it crashed again. I wrote a short script to just see what the pulses look like and I get mostly random looking pulse widths. I heard some good stuff about them. Feel free to share it: January 6, at 5: This site uses cookies.

November 26, at January 6, at 3: Post was not sent – check your email addresses! Face following OpenCV on Android. Last edited by Paulus; Jun 24, at However, Schulze 8 and 4 ch Rx are working even better in that use.

Graupner R700 Receiver

Flying along in level flight at high speed when it suddenly went berserk – snapped into a spin and wound up at the top of a foot tree. I did try your code snippet above.

Arduino Servo Library – Not good enough. Silly me – should have done some serious range checking and maybe flown it in a different plane.

I always have had great results with Hitec Super Slim’s. Leave a Reply Cancel reply Enter your comment here You are commenting using your WordPress. Hey Dan, It works! Although single conversion, it has some software to reject bad signals and is virtually glitch free in F5D.

Thanks for posting this article. July 30, at 9: Thanks in advance, Paul. They have SPCM and work very well – no problems at all. Wii motion plus and Arduino.


Never a glitch and it is flown to the limits of visability. Originally posted by Paulus I had an schulze 8 in my crashed gilette. TM Display driver for Stellaris Launchpad. Graupnner 26, at 9: If you found any of this stuff interesting…. Chris True Registered User.

It saved me a lot of poking around my receiver to find the PPM. Email required Address never made public. If I want to use it with arduino 8Mhz what I have to change in timer? I think I’m going to try a DS19 or one of the hitec dc receievers. I have one in my El Bandito, it sits 1 inch over a 22 cell pack with amp current draws, the ESC and wiring is on grau;ner bottom of the fuse about 5 inches away and runs right past it back to the fan which is 8 inches or so to the rear.

Create a free website or blog at WordPress. July 31, at Notify me of new posts via email. Hi, I have this: These range check over feet on my Jr