Home  /   LP2950 DATASHEET PDF

General Description. The LP and LP are micropower voltage regulators with very low dropout voltage (typically 40mV at light loads and mV at. LPLPRE3 Texas Instruments LDO Voltage Regulators FIXED MICROPWR VLTG REG datasheet, inventory, & pricing. The LP and LP are micropower voltage regulators with very Careful design of the LP/LP has minimized all . See MIL/AERO Datasheet.

Author: Dulmaran Badal
Country: Liechtenstein
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 13 August 2015
Pages: 30
PDF File Size: 20.32 Mb
ePub File Size: 2.74 Mb
ISBN: 649-5-70397-784-4
Downloads: 87631
Price: Free* [*Free Regsitration Required]
Uploader: Tahn

Did you look at the datasheet from that company? The board is shown below. I just tried taking a regulator part not on a board and applied from 4. Shop Blog Forum Support.

I expect that the regulator can tolerate this but it might add some unnecessary current drain. It looks like the detector is on the same side as the display – does this mean you are checking yourself for radiation rather than pointing it at a source dztasheet front of you?

Datasheer for checking on the regulator — maybe I shorted the power supply while hooking things up. Is the RS option useful? I especially like the plated through holes, which are fantastic for prototyping if you have to remount datahseet several times.

I had to jump! There is one error in the published circuit: Dattasheet below for the exterior appearance. Both have a thin and very delicate metalized membrane for measurement of alpha radiation. I could post the entire project if you think it would help sales of the ATtiny26 board.

Can you tell me what you like about it? Since there datashedt some interest, my Geiger counter is based on a circuit described by Tom Napier in Circuit CellarNovember Well, I connected a 4. By the way, I really like the board design. There is a small current draw increase at 5. It features an internal V power supply 2 mA total draw! I suspect that no long term damage should result from this misuse, as long as one does not exceed other component ratings.


The HV generator is top right, leading to the connector for the V tube bias red arrow. I do that sort of thing all the time, and I have had no problems.

National Semiconductor – datasheet pdf

The program currently occupies out of bytes of program memory. I could post the entire project if you think it would help sales of the ATtiny26 board I do intend to buy a few more — the sale price is very attractive, so be sure and save me a couple!

Beta and gamma radiation are much more penetrating so the direction the tube is pointing is less important and is actually irrelevant for gamma radiation.

Of course we had these boards made in a batch, so now each time I populate one I have to bypass the power switch with tweezers to to clear that fuse. What puzzles me is that the regulator encounters this situation every time the external source is switched off and there are capacitors in the circuit that must be discharged, so there is some reason to think that such a transient backflow is not damaging. Not realizing this we designed our main board which uses the pushbutton power switch with one of these connected to the OFF pin.

Can you try doing the regulator test again? In my version, the tube is screened so that small sources can be set right on top of the detector. Fortunately, I disconnected it quickly enough to prevent any obvious permanent damage to the regulator. Where did you get your Geiger tube?

LP Datasheet Alpha Semiconductor pdf data sheet FREE from

By the way, there are a few manufacturers of the part, and your board probably has the one from On Semiconductor. The C program and the two buttons provide a menu-based system to set up data collection parameters and do the counting. If only the ATtiny26 had a bit more memory… Thanks, Jim. For one low-power project, I have the possibility of powering the board from either a 9V solar cell or a 4.


We would probably buy a few, especially if the footprint was compact. We even had some ATmega8 versions made, but we never sold them there were some other factors besides the ATtiny26 board not doing well, such as the mega coming out and the move to 6-pin ISP connectors. My most recent project with the ATtiny26 board is a Geiger counter.

Datasheets search archive of electronic components datasheets

I do intend to buy a few more — the sale price is very attractive, so be sure and save me a couple! The LP data sheet does not give any insight into this situation. What I like about the ATtiny26 board is the convenient arrangement of two ports with access to power and ground at several points, coupled with the well-laid out prototyping area. The rainbow cable leading off screen goes to the two pushbuttons and the LCD. The JTAG fuse comes set, which makes some pins start up set high.

The unit is currently monitoring the cosmic background radiation in my office 95 counts in seconds. If I connect the 4. I can always use diodes to switch between solar and backup supply, but I thought I could float charge the battery without such trickery. My power supply current-limited at about 1 amp.

The counter input INT0 is marked with a green arrow.